·设为首页
·加入收藏
 产品分类
电机
泵类
减速机
风机
发电机
电焊机
空压机
电线电缆
车、铣、钻床
起重机械
建筑机械
液压气动
矿山机械
橡胶制品
链轮链条
五金工具
化工设备
轴承大全
汽保设备
磨料磨具
环保设备
伟德BETVICTOR下载
清洗机
石家庄螺杆空压机
伟德BETVICTOR下载

在清洗、拆卸或保养维护前,关掉空气和喷涂材料的输入阀,扣动扳机卸掉空气和液体压力。
 
 1、使用后,迅速彻底清洗伟德国际苹果app帽和液体喷嘴,清洗不彻底将产生不好的喷幅和表面质量。清洗时,将剩余涂料倒掉用少量稀释剂清洗涂料通道伟德国际苹果app嘴。
 2、用所附带的浸过稀释剂的刷子或抹布清洗其它部分。
 3、每天用微量机油涂注在针垫片、开关垫片、幅调钮垫片、扳机轴接着。
 4、除去涂料针之后或当其被摘下来时将液体喷嘴也摘除,这样来保护针座部分。
 5、当喷针装置插入时,用手紧固喷针密封装置。然后再用扳手慢慢紧固。拉动扳机观察喷针的运动情况,调节密封圈装置。拉动扳机观察喷针的运动情况,调节密封圈装置。因为太紧会降低喷针的运动速度并导致液体在喷嘴尖端的泄露。若紧固的不够,则可能导致空气进入,影响喷涂。
 6、开启喷幅调节旋钮,反时针旋转至充分打开。顺时针旋转为缩小喷涂宽度,旋至底为关闭喷涂宽度呈圆形喷涂。

Cleaning, demolition or maintenance for the former, turn off the air and spray material input valve, pull the trigger removal of the air and liquid pressure.

1, after use, fast and thorough cleaning liquid spray nozzle cap, not thorough cleaning will have a bad spray rate and surface quality. Cleaning when
Discard the remaining paint with a small amount of paint thinner, cleaning spray nozzle channel.
2, with the attached brush or rag soaked in thinner, cleaning other parts.
3, micro motor oil every day in the needle injection pads, switch gaskets, gasket rate adjustment button, then the trigger shaft.
4, remove the needle after the paint or when it is picked and the liquid when the nozzle is also removed, so to protect the needle seat section.
5, when the jet needle insertion device, hand tighten the spray needle seal. And then use the wrench slowly tightening. Pull the trigger conditions observed the movement of needles
Conditions, adjusting ring device. Pull the trigger observe the movement of needles, adjusting ring device. As too tight will reduce the speed of movement of needles
Degree and lead to leakage of liquid in the nozzle tip. If the tightening is not enough, it may cause air to enter and affect spray.
6, open the spray rate adjustment knob fully anti-clockwise rotation to open. Clockwise to narrow the spray width, spin to the end to close the spray width
Rounded spray.

安全警告
 
 1、液体和溶剂十分易燃,应在通风良好的伟德国际苹果app橱中使用,避免所有点火源,如吸烟、明火、电灯等。
 2、禁止使用卤代火烴溶剂,它们可与铝和铜的零件发生化学反应导致爆炸。所用的所有液体和溶剂应与铝和铜零件兼容,不与之发生反应。
 3、为减少静电擦火的危险,应始终保持喷涂装置所喷涂对象的接地连惯性。
 4、不要指向人体喷涂。
 5、不要超出设备的最大安全工作压力。
 6、喷涂时所产生的毒气会导致中毒和严重的身体危害请在通风良好的区域使用伟德BETVICTOR下载,操作人员戴保护性眼睛、手套、呼吸器等等。

Safety Warning
1, liquids and solvents are very flammable and should be well-ventilated spray hood, to avoid all ignition sources such as smoke, fire, lights and so on.
2, prohibit the use of halogenated hydrocarbon solvent fire, they can be aluminum and copper parts with a chemical reaction caused an explosion. Used in all liquids and solvents should be
Compatible with aluminum and copper parts, do not react with it.
3, to reduce the risk of static friction fire, should always keep the spray coating equipment grounding object coherence.
4, do not point to the body spray.
5, do not exceed the maximum safe working pressure of equipment.
6, poisonous gas produced when spraying can cause poisoning and serious bodily harm in a well-ventilated area, please use the gun, the operator wear eye protection, gloves, respirators and so on.

gravity spray gun



共分为1页 [1] 当前第1/1页
版权所有:Copyright 河北省石家庄安界机电设备有限公司 地址:河北省石家庄市和平东路129号   冀ICP备09046541号